Full |
Ⅰ Software Download
【Software】 【Driver】 【Firmware】 【Manual】
Ⅱ Standard Accessories
Ⅲ Powerful Function
Ⅳ Feature
• Isolated level:1000V CATII,600V CATIII.
• High Bandwidth 60MHz-200MHz Oscilloscope,1GSa/s sample rate, and 6000 Counts DMM with analog bargraph , and data recorder.
• 1M Memory Depth.
• High Refresh Rate (2500 frames)
• Large 5.6 inch TFT Color LCD Display,High Resolution(640*480), Dual-Window Design --More clear, More Detailed
•
One-touch automatic setup optimizes the position, range, timebase, and
triggering to assure a stable display of virtually any waveform
• Easy-to-use pop-up menu with built-in multi-language help system
• 23 Automatic Measurements
• Waveform Math: Add, Subtract, Multiply, and Divide
• Store and recall over
• Automatic cursor tracking measurements
• XY Mode
•
Built-in FFT function converts a time-domain signal into its frequency
components to measure harmonic content and distortion in systems
• Waveform Recorder to capture/replay input waveforms from CH1 and CH2 with a maximum record length of 1000 frames
• Pass-Fail function compares a stored waveform to an unknown input
• Average Mode for smoothing waveforms
• Square Wave Output (2V, 1kHz) for probe adjustment
• USB Host/Device 2.0 full-speed interface ,support removeable disk, LAN Optional ,Easy to control by PC or long-distance.
• Dimensions (mm):240(L)x165(W)x50(H), be carried easily.
Ⅴ Specification
Model
|
DSO1202S
|
DSO1122S
|
DSO1062S
|
Oscilloscope Mode
|
Vertical
|
Bandwidth
|
200MHz
|
120MHz
|
60MHz
|
Real-time Sample Rate
|
1GSa/s
|
Equivalent Sample Rate
|
25GSa/s
|
Record Length (Sample Points)
|
Single-channel: Maximum 2M; Dual-channel: Maximum 1M
|
SEC/DIV Range
|
2nS/div-2000S/div (in a 2, 4, 8 sequence)
|
A/D Converter
|
8-bit resolution
|
VOLTS/DIV Range
|
2mV/div~5V/div at input BNC
|
Position Range
|
±50V(5V/div),±40V(2V/div~500mV/div),±2V(200mV/div~50mV/div)±400mV(20mV/div~2mV/div)
|
Rise Time at BNC
|
≤1.7ns
|
≤2.9ns
|
≤5.8ns
|
DC Gain Accuracy
|
±4% for Sample or Average acquisition mode, 5mV/div to 2mV/div ±3% for Sample or Average acquisition mode, 5V/div to 10mV/div
|
Trigger
|
Trigger Sensitivity (Edge Trigger Type)
|
DC: CH1/CH2(Typical) 1div from DC to 10MHz;1.5div from 10MHz to Full AC: Attenuates signals below 10Hz
HF Reject: Attenuates signals above 80kHz
LF Reject: Attenuates signals below 150kHz
Noise Reject: Reduces trigger sensitivity
|
Trigger Level Range
|
CH1,CH2: ±8 divisions from center of screen
|
Hold off Range
|
100ns-10s
|
Trigger Level Accuracy,typical (Accuracy is for signals having rise and fall times ≥20ns)
|
CH1,CH2: ±(0.3div×V/div) (within ±4 divisions from center of screen)
|
Trigger Type
|
Edge
|
Trigger on the rising or falling edge
|
Video
|
Trigger on an NTSC, PAL, or SECAM standard video signal Line Range: 1-525 (NTSC), 1-625 (PAL/SECAM)
|
Slope
|
Trigger (when >,<,=,≠) on a positive or negative slope Set Time: 20ns–10s
|
Overtime
|
From the rising or falling edge Set Time: 20ns-10s
|
Alternate
|
Internal trigger on edge, pulse width, video or slope
|
Measurement
|
Cursors
|
Manual: The difference between voltage cursors △V; the difference between time cursors △T; 1/△T calculated by Hz. Tracing: The voltage and time at a waveform point
|
Automatic(32)
|
Frequency,
Period, Mean, Pk-Pk, Cycli RMS, Minimum, Maximum, Rise time, Fall Time,
+Pulse Width, -Pulse Width, Delay1-2Rise, Delay1-2Fall, +Duty, -Duty,
Vbase, Vtop, Vmid, Vamp, Overshoot, Preshoot, Preiod Mean, Preiod RMS,
FOVShoot, RPREShoot, BWIDTH、FRF、FFR、LRR、LRF、LFR、LFF
|
|
Meter mode
|
|
Max. Resolution
|
6,000 Counts
|
DMM Testing Modes
|
Voltage, Current, Resistance, Capacitance, Diode & Continuity
|
Max. Input Current
|
AC: 10A, DC: 10A
|
Input Impedance
|
10 MΩ
|
Isolation
|
The float voltage between BNC and Ground
|
600V CATIII, 1000V CAT II
|
The float voltage between each Channel
|
600V CATIII, 1000V CAT II
|
The float voltage between Multimeter and Ground
|
1000V
|
between input Ports directly
|
400V CAT II
|
Input by 10:1 probe
|
600V CATIII, 1000V CAT II
|
The Max input voltage of Multimeter
|
The float voltage between Multimeter and Ground
|
Display
|
Type
|
Right angle 5.6 16-digit color LCD
|
Resolution
|
640*480 dots
|
Contrast
|
16 gears, with the progress bar to show adjustment
|
Interface
|
USB host and USB slave, LAN Optional
|
Power
|
Voltage
|
DC Input:12--17VDC, 2000mA
|
Measurement
|
Size
|
245 x 163 x 52 (mm)
|
Weight
|
0.35kg
|
Ⅵ Software Support
Operating System: Windows NT, Windows 2000, Windows XP, VISTA, Windows 7.
|
Hiç yorum yok:
Yorum Gönder